Understanding Essential Plumbing Skills is Crucial for Bathtub Installation
Understanding Essential Plumbing Skills is Crucial for Bathtub Installation
Blog Article
We've found this post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the internet and thought it made perfect sense to talk about it with you on my blog.
Setting up a tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult task. If the old bathtub is easily obtainable, the job can move rapidly; if you have to open a wall to get rid of the old tub and place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old tub as well as embeded in the brand-new one. Make sure you have certified on your own for the task as well as are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need a specialist plumber to make tube links.
This short article will aid you mount a brand-new bath tub in your restroom if you have actually already gotten a new tub and don't require to alter the setup of your previous water supply pipes.
Your devices and also product checklist ought to comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the limited accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in area between the faucet and also the sink. Secure the faucet in position with the maker supplied backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former type needs to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the needed setting. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bath tub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water supply and also inspect all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise examine the overflow electrical outlet and the regular outlet for leakages.
Finally, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bathtub must wait until the bath tub has been used at the very least when as this will certainly settle it right into its last setting.
Preparing for the Setup
First of all, the sustaining structure supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, causing difficulties with moisture and also feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealant can break fairly early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that entry on Tools You Need to Install a New Bathtub when surfing around the search engines. Sharing is good. Who knows, you might be doing someone a favor. Thanks a lot for your time. Kindly visit our site back soon.
Fast and effective, call! Report this page